Bunion Splint (Hallux Valgus) – Tynor K14
The Tynor Bunion Splint is a hinged big-toe splint designed to help hold the big toe in a straighter, more aligned position for hallux valgus (bunion). It can also be worn after bunion surgery to help maintain the toe's alignment. A dynamic motion hinge keeps the foot flexible, so the splint can be worn while walking, as a day or night splint, and the cushioned ball-joint pad is designed to support the transverse arch. Supplied by Australian Healthcare Supplies, a registered NDIS provider based in Perth, Western Australia.
Features
- Dynamic motion hinge that flexes with the toe, so the splint can be worn while walking
- Strong, ventilated moulded polymer shell, anatomically shaped to suit almost every foot size
- Cushioned ball-joint pad, designed to support the transverse arch and help unload the ball of the foot
- Soft, adjustable mid-foot and toe straps for a secure, customisable fit
- Trimmable main strap with a Y hook-tape clamp for a tailored length
- Bilateral, ambidextrous — fits either foot
- Slim enough to wear inside a wide-front shoe
- Suitable as a day or night splint
Intended Use
May assist in managing discomfort associated with the following conditions:
- Bunions (hallux valgus) of the big toe
- Big-toe mal-positioning
- Support following bunion surgery
- Congenital deformities of the big toe
- Arthritis or inflammatory joint conditions of the big toe
How to Use
- The splint is one universal size and can be worn on either foot.
- Release the hook-and-loop fasteners on the mid-foot (large) and toe (small) straps to loosen them.
- Slide the splint onto the foot so the hinge sits directly over the big-toe joint.
- Hold both ends of the large strap and the splint, draw the strap ends together and fasten — one tab to the lower side, one to the upper.
- Tighten the toe strap in the same way.
- Place the ball-joint pad on the underside of the foot, under the large strap, so its edge does not extend past the centre of the hinge; use it whenever walking (unless special insoles are worn).
- Build up wear time gradually, and use as directed by your healthcare professional.
What's in the Box
- 1 x Tynor Bunion Splint (K14)
- 1 x Ball-joint arch pad
- 1 x User manual
Product Care
- Hand wash with mild detergent in water below 30°C; do not wring.
- Close the hook-and-loop fasteners before washing.
- Dry in the shade on a flat surface.
- Do not dry-clean.
- Do not iron.
- Do not bleach.
Important Cautions
- Use under the guidance of a qualified healthcare professional.
- In the beginning, wear for only a few hours to get used to it, then build up wear time gradually.
- Tighten enough to hold the toe in position while keeping it comfortable and bearable — do not over-tighten.
- Ensure there is no constriction; avoid ill-fitting or pointed shoes and choose wide-front, slightly oversized footwear.
- Do not wear while swimming or at the beach.
- Discontinue use and consult a qualified doctor if you experience impaired sensation, impaired blood flow, allergic rash or itching, or if pain increases or persists.
- Consult your doctor in the case of concurrent use with any other medical device.
- Misuse or improper use of the device can lead to adverse effects and reduced performance.
- Keep out of reach of children.
Common Questions
What is the Bunion Splint designed to do?
It is designed to help hold the big toe in a straighter, more aligned position for hallux valgus, and can also be worn after bunion surgery to help maintain alignment.
Can I wear it while walking?
Yes. The dynamic hinge flexes with the toe, so it can be worn during walking, both day and night. Use the ball-joint pad whenever you walk in it.
Does it fit either foot?
Yes. One universal size fits either the left or right foot and most toe sizes.
How long should I wear it at first?
Start with just a few hours to get used to it, then increase wear time gradually as advised by your healthcare professional.
Regulatory & Supply Details
Product Code: K14
Sizes Available: Universal
Device Classification: Class I Medical Device
Certifications: ISO 9001 · ISO 13485 · ISO 45001 · US FDA Registered · CE Marked · W.H.O. GMP
Manufacturer: Tynor Orthotics Pvt. Ltd.
EC Representative: MT Promedt Consulting GmbH, Altenhofstraße 80, D-66386 St. Ingbert, Germany
Australian Supplier: Australian Healthcare Supplies, Perth WA — registered NDIS provider
Bulk orders: Contact our team for bulk or NDIS pricing