R.O.M. Knee Brace 22"/56cm
The Tynor ROM Knee Brace 22"/56cm (D48) is a hinged, universal-fit brace designed to control and restrict the degree of knee flexion through a multi-point fixation system, allowing either a controlled range of motion or immobilisation at any angle. Its Multi-Point Fixation Graduated Disc (MPFGD) hinges can be adjusted by a simple pull-and-rotate action, while a three-layered neoprene-bonded wrap and reverse-buckle straps hold the brace securely. The lightweight, bilaterally symmetric design fits most patients and can be worn on either leg. Supplied by Australian Healthcare Supplies, a registered NDIS provider based in Perth, Western Australia.
Features
- ROM dial allows locking at any angle, or controlled motion between any two angles, adjusted with an easy pull mechanism.
- Multi-Point Fixation Graduated Disc (MPFGD) hinges connected to lightweight, rigid bars, with 10° intervals between adjacent pins.
- Three-layered neoprene-bonded fabric wrap with a silicone-coated liner for grip, cushioning and to help prevent migration.
- Ergonomic, bilaterally symmetric design with a universal fit for either leg, designed for comfortable use over long hours.
- Reverse-buckle straps for controlled tightening, enhanced grip and easy application.
Intended Use
May assist in managing discomfort associated with the following conditions:
- Post-operative treatment and rehabilitation of the knee
- Support and stability for a weak or injured knee joint
- Protection of the knee from unexpected load and motion
- Restriction of excessive range of knee joint motion
- ACL and PCL injuries
- Osteoarthritis of the knee
How to Use
- Set the flexion angle first: pull the knob lightly, rotate and release at the desired angle on the graduated disc, then bend the knee to confirm the angle.
- Set the extension angle in the same way on the extension side, and repeat for the other hinge.
- Affix the two hinges on either side of the knee so the centre of the MPFGD aligns with the axis of the knee, keeping the hinges upright per the arrow mark.
- Wrap the Velcro bands around the leg one by one, passing them through the slots in the buckle, and fasten with the reverse buckle for a secure, comfortable grip.
- For immobilisation, move both flexion and extension knobs to the same angle; for free flexion, set the flexion knob to 120° and the extension knob to 0°.
What's in the Box
- 1 x Tynor ROM Knee Brace 22"/56cm (D48)
- Product manual
Product Care
- Hand wash with mild detergent in water below 30°C without wringing.
- Dry in shade on a flat surface.
- Do not dry-clean and do not bleach.
- Close hook-and-loop fasteners before washing.
Important Cautions
- Use this product under the guidance of a qualified doctor or healthcare professional.
- Discontinue use and seek advice if you notice impaired sensation, impaired blood flow, allergy, rash or itching, or if pain increases or persists.
- Misuse or improper use of the device can lead to adverse effects and decreased effectiveness.
- Adjust padding and strapping for a secure, comfortable fit; the product is preferably worn over a cotton lining or undergarment.
- Keep out of reach of children.
- Please check with your doctor, physiotherapist, or healthcare professional to confirm this product is suitable for your condition and correct sizing.
Common Questions
Can I lock the knee at a set angle? Yes, moving both the flexion and extension knobs to the same angle immobilises the knee at that position.
Does it fit either leg? Yes, the bilaterally symmetric, universal design can be used on the left or right leg.
What are the adjustment intervals? The graduated disc has 10° intervals between adjacent pins for flexion and extension settings.
Is it one size? Yes, it has a universal, one-size-fits-most design.
Regulatory & Supply Details
- Product Code: D48
- Sizes Available: Universal
- Device Classification: Class I Medical Device
- Certifications: ISO 9001 · ISO 13485 · ISO 45001 · US FDA Registered · CE Marked · W.H.O. GMP
- Materials: Aluminium, Polypropylene, Steel, Neoprene, Polyester, Polyamide
- Manufacturer: Tynor Orthotics Pvt. Ltd.
- EC Representative: MT Promedt Consulting GmbH, Ernst-Heckel-Straße 7, 66386 St. Ingbert, Germany
- Australian Supplier: Australian Healthcare Supplies, Perth WA — registered NDIS provider
- Bulk & wholesale orders: sales@tynor.com.au