Pelvic Traction Kit with Weight Bag
-
Size
The Tynor Pelvic Traction Kit with Weight Bag (G24) is a complete traction system designed to apply uniform, controlled traction to the lumbar, sacral and thoracic areas of the vertebral column. The pelvic belt holds the pelvic area like a halter, and its oblique traction straps are designed to direct the force to the spine rather than the lateral sides of the pelvis. The kit connects the belt to a spreader bar, traction pulley bracket, traction cord and a fillable weight bag, so it can be set up at home or in a clinic. Supplied by Australian Healthcare Supplies, a registered NDIS provider based in Perth, Western Australia.
Features
- Complete home or hospital traction kit — belt, spreader bar, pulley bracket, cord and weight bag
- Pelvic belt made from three-layered PU-bonded fabric with a cushioning PUF middle layer
- Large hook-and-loop area for a customised, adjustable fit and grip
- Oblique traction straps designed to focus force on the LS vertebrae
- Versatile pulley bracket with an adjustable-angle arm to suit most beds
- Fillable weight bag for controlled, uniform traction load
Intended Use
May assist in managing discomfort associated with the following conditions:
- Lumbar spondylosis
- Intervertebral disc syndrome
- Lower back ache
- Postural fatigue and postural deformities
- Mechanical stress due to poor posture
- Stabilisation during vertebral fractures or injuries (under professional guidance)
How to Use
- Wrap the belt around the pelvic area with the traction straps on the underside.
- Hook the traction straps to the spreader bar and traction pulley bracket.
- The spreader bar helps balance the traction force equally on both sides of the body.
- Fill the weight bag to the load calculated by your clinician and connect it via the traction cord and pulley.
- Lie on a hard, smooth surface or hospital bed for effective traction, under the strict guidance of a qualified doctor or physiotherapist.
What's in the Box
- 1 x Pelvic Traction Belt (size as ordered)
- 1 x Spreader Bar
- 1 x Traction Pulley Bracket
- 1 x Traction Cord (10 ft)
- 1 x Traction Weight Bag (supplied empty)
Product Care
- Belt and traction cord: cold hand wash in mild detergent without wringing; dry in shade on a flat surface.
- Do not iron, dry-clean, bleach or use a brush on the fabric parts.
- Pulley bracket, spreader bar and weight bag: clean with a simple wet wipe, with or without detergent.
Important Cautions
- This equipment should be used under the strict guidance and vigil of a qualified doctor only.
- The weight of traction and counter-traction should be carefully calculated by a qualified expert.
- Keep a careful watch for any adverse symptoms during the entire traction period.
- Discontinue use and seek guidance from a qualified doctor in the case of impaired sensation, impaired blood flow, allergy, rash or itching, or if pain increases or persists.
- Misuse or improper use of the device can lead to adverse effects and reduced effectiveness.
- Follow the instructions supplied on the box carefully.
- Keep out of reach of children.
- Please check with your doctor, physiotherapist, or healthcare professional to confirm this product is suitable for your condition and correct sizing.
Common Questions
Is this a complete kit?
Yes. The kit includes the pelvic belt, spreader bar, traction pulley bracket, traction cord and weight bag.
What sizes are available?
The pelvic belt comes in Small, Medium, Large and Extra Large. Measure the circumference 3 inches below the navel to select your size.
What weight should I use?
The traction load must be calculated by a qualified orthopaedic doctor or physiotherapist for your individual needs.
Do I need a special bed?
For effective traction, lie on a hard, smooth surface or hospital bed. The pulley bracket adjusts to suit most beds.
Regulatory & Supply Details
- Product Code: G24
- Sizes Available: Small, Medium, Large, Extra Large (belt circumference 80–140 cm, measured 3 in below the navel)
- Device Classification: Class I Medical Device
- Certifications: ISO 9001 · ISO 13485 · ISO 45001 · US FDA Registered · CE Marked · W.H.O. GMP
- Materials: Polyester, Rubber, Polyurethane, Polyamide, Steel, Polypropylene, PVC, Cotton
- Manufacturer: Tynor Orthotics Pvt. Ltd.
- EC Representative: MT Promedt Consulting GmbH, Ernst-Heckel-Straße 7, 66386 St. Ingbert, Germany
- Australian Supplier: Australian Healthcare Supplies, Perth WA — registered NDIS provider
- Bulk & wholesale orders: sales@tynor.com.au
Size Chart
